Last reviewed · Works with wired, wireless and gaming mice and laptop touchpads
Quick answer: click each button on the on-screen mouse, scroll the wheel, and move the pointer inside the tracking area. If a button does not light up, the wheel skips, or one click counts twice, you have found a hardware problem. The built-in CPS counter shows your clicks per second at the same time.
How to Use the Mouse and Touchpad Tester
- Choose Physical Mouse or Laptop Touchpad with the switch above the tester.
- Press the left, right and middle buttons. Each one lights up on the on-screen mouse while it is held down.
- Scroll the wheel up and down to confirm both directions register smoothly.
- Move the pointer across the tracking area and watch the glowing dot follow it.
- Click quickly for a few seconds to measure your CPS (clicks per second) and watch the Clicks total.
How to Detect a Mouse Double-Click Problem
As a mouse switch wears out, a single press can register as two clicks. This is often called double-click chatter and it causes accidental double-clicks, broken drag-and-drop and files opening when you only wanted to select them. To check for it:
- Click the left button once, slowly and firmly.
- Look at the Clicks counter. If it went up by two, the switch is bouncing.
- The tester shows a warning when two clicks arrive within about 100 milliseconds. Treat this as an estimate; only a hardware diagnostic can confirm a failed switch.
Before you replace the mouse, rule out settings: in Windows, open Mouse settings and check the double-click speed, and turn off ClickLock if it is enabled. If the problem remains on a second computer, the switch is worn. Many gaming mice have replaceable switches, and a mouse that is still under warranty can often be exchanged.
Testing the Scroll Wheel and Pointer Tracking
Scroll slowly in both directions. The wheel should respond in both directions without jumping or reversing. If the page jumps back up while you scroll down, the encoder inside the wheel is probably dirty or worn. In the tracking area, move the pointer smoothly in circles and straight lines. A dot that stutters, freezes or jumps points to a dirty or faulty optical sensor, a poor surface (glass or glossy desks are common culprits) or a wireless connection that needs a closer receiver.
Understanding CPS (Clicks Per Second)
CPS is the number of clicks you register in one second. Casual users usually land somewhere around 5 to 7 CPS in a short burst, and higher scores come from techniques such as jitter or butterfly clicking. The CPS value here is calculated from the clicks registered in the last second, so it also helps you notice when your mouse drops clicks: if you are clicking fast and the counter falls behind, the button may not be recovering quickly enough. Use it as a fun practice tool and as a rough check, not as a precise benchmark.
Understanding Touchpad Limitations
When you choose Laptop Touchpad, a virtual pad appears. A web page cannot read the raw sensor of a touchpad; it only sees the pointer and touch events your operating system produces. If your paint trail has gaps, your driver may be dropping events, your finger may be too dry, or the surface may be dirty. For deeper hardware checks, use the diagnostic tool from your laptop manufacturer.
Quick Troubleshooting Table
| Symptom | Likely cause | What to try |
|---|---|---|
| One click counts twice | Worn switch or wrong double-click speed setting | Check OS settings, test on another PC, then replace the switch or the mouse. |
| Button does not register | Switch failure or loose cable | Try another USB port; test wired if the mouse is wireless. |
| Scroll jumps or reverses | Dirty or worn scroll encoder | Blow out dust with compressed air; replace if it continues. |
| Pointer stutters | Dirty sensor, bad surface or low battery | Clean the lens, use a mouse pad, charge or replace batteries. |
| Pointer drifts or jumps | Wireless interference | Move the receiver closer using a USB extension cable. |
Typing problems too? Run our keyboard tester next, or check a game controller with the gamepad tester.
Frequently Asked Questions (FAQ)
What is CPS and how is it calculated?
CPS stands for clicks per second. The tool counts the clicks registered within a rolling one-second window. Gamers use it to practise rapid clicking, and it also reveals when a button misses fast presses.
Why does my right-click menu not appear in the test area?
We hide the standard browser menu inside the test area so you can test the right button without pop-ups. If the on-screen mouse does not light up when you right-click, the right button itself may be faulty.
Is this tool accurate for diagnosing hardware?
It is accurate for software-level input such as clicks and scroll events. It cannot measure the physical durability of a switch or the raw polling rate and DPI of the sensor.
How do I know if my mouse is double-clicking?
Click once, slowly. If the Clicks total increases by two, or the double-click warning appears, the switch is registering a click twice. Check your operating-system double-click settings first, then test the mouse on another computer.
Can I test a laptop touchpad?
Yes. Switch to Laptop Touchpad mode and drag your finger over the pad. This tests the touch events your operating system reports, not the raw sensor.
Does the tool test my mouse DPI or polling rate?
No. Browsers cannot read DPI or the true polling rate. Use your mouse manufacturer's software for those settings.
Is my mouse activity recorded?
No. Everything runs locally in your browser and nothing is sent to a server.